Arduino IDE 2.3.2
Board: ESP32S3 Dev Module (ESP32 by Expressif Systems)
TFT_eSPI Lib version: 2.5.43

The serial monitor output during boot is shown below:

20:23:38.744 -> Core 1 register dump:
20:23:38.744 -> PC : 0x4202731f PS : 0x00060a30 A0 : 0x820273f4 A1 : 0x3fcebc60
20:23:38.777 -> A2 : 0x00000010 A3 : 0x00000000 A4 : 0x60004000 A5 : 0x0000000d
20:23:38.777 -> A6 : 0x000000ff A7 : 0xff000000 A8 : 0x08000000 A9 : 0x3fcebc30
20:23:38.777 -> A10 : 0x3fcb6d90 A11 : 0x00000001 A12 : 0xffffffff A13 : 0x00000004
20:23:38.777 -> A14 : 0x00000000 A15 : 0x3fc92920 SAR : 0x00000010 EXCCAUSE: 0x0000001d
20:23:38.813 -> EXCVADDR: 0x00000010 LBEG : 0x4202bbe0 LEND : 0x4202bc43 LCOUNT : 0x00000000
20:23:38.813 ->
20:23:38.813 ->
20:23:38.813 -> Backtrace: 0x4202731c:0x3fcebc60 0x420273f1:0x3fcebc90 0x420273fc:0x3fcebcb0 0x42001f3a:0x3fcebcd0 0x4202c9ba:0x3fcebd40
20:23:38.813 ->

Barbot can hold and accurately dispense 9 bottles of ingredients to create the perfect cocktail mix ❗️

What you’ll need?:

• Arduino Mega 2560
• NEMA 17 stepper motor
• Pololu A4988 stepper driver
• Hitec HS-7955TG servo motor
• Pololu Micro Maestro 6-Channel Servo Controller
• HC-05 Bluetooth Module
• GT2 6mm wide timing belt
• GT2 timing pulley 20 teeth 5mm bore
• Timing belt bearing
• 2x Chrome plated round rail 1200mm x 12mm
• 4x SK12 12mm bore linear rail shaft support
• 4x SC12UU aluminium pillow block housing
• 9x 20ml Beaumont Metrix SL spirit measure
• 3x Wall 3 bottle rack
• Endstop microswitch
• Cable carrier
• DC-DC converter (12v to 5V)
• AC power supply 12V (6.67A)

2️⃣Farmaid: Plant Disease Detection Robot?️

This project can help you who are engaged in agriculture find and build a robot that can help you detect and mark diseased crops without destroying the farm environment ❗️

What you’ll need?:

• Mountain Ark SR 13 chassis
• Arduino UNO Rev3
• 2x Raspberry Pi 3 Model B or newer
• Female/Female Jumper Wires
• Male/Female Jumper Wires
• Male/Male Jumper Wires
• ibt-2 HBridge
• 2x Raspberry Pi Camera Module
• TensorFlow

3️⃣Self-Playing Melodica?️

This project shows you how to use the DC motor of an old printer and some basic components to build a self-performing Melodia❗️

What you’ll need?:

• Arduino Nano R3
• 2x Resistor 1k ohm
• 2x Dual H-Bridge motor drivers L298
• 2x Pushbutton Switch, Momentary
• Digilent 60W PCIe 12V 5A Power Supply
• Voltage regulator, step-down, 12V in, 3.6V out
• Bistable electrovalve (solenoid)
• DC Motor, 12 V (You can always buy a DC motor if you don’t have an old printer Dc motor!)

4️⃣PEZ Robo Dispenser Using Arduino?️

Building the PEZ Robo candy dispenser can evoke the childhood memories of many people❗️

What you’ll need?:

• The PEZ Robo Dispenser
• Arduino UNO Rev3 // Seeeduino V4.2
• Ultrasonic Distance Sensor HC-SR04 // Grove – Ultrasonic Distance Sensor
• RC Servo
• Breadboard
• Jumper wires
• Wire fasteners or rubber bands
• Battery (Anything over 7 volts with about 500mAh)

5️⃣Maze Solver Robot, using Artificial Intelligence?️

By giving it a certain degree of intelligence, this robot can pass through any maze in the shortest possible time❗️

What you’ll need?:

Arduino Nano R3 // Seeeduino Nano

HC-06 Bluetooth Module

TCRT5000 4CH Infrared Line Track Follower Sensor Module

2x SparkFun RedBot Sensor – Line Follower

ZX03 (based on TCRT5000) Reflective Infrared Sensors (Analog output)

Android Device

2x RobotGeek Continuous Rotation Servo

2x 4xAA battery holder