This order was cancelled a few days ago, but this morning I clicked the "Pay Now" button and completed the payment via VNQR. However, when I check the status of my order, it is still showing as cancelled.

Could you please process this order and ship it to me now that the payment has been made?

Thank you for your assistance.

Is there a specific model you recommend? I know you’ve said CM5 Lite, but is that model SC1560?

Thanks,

BTW, I tried sending a Chat Request but it always says everybody is offline. I sent an email 2 days ago and that has not been responded to. Hopefully this post will not go unanswered.

Thanks,
Mark

To help these makers bring their ideas to life more easily, we launched the Partner Seller strategic program. This is not just a typical affiliate program — it is a tailored, one-stop service designed for makers, students, and engineers. It covers production services, free warehousing, free promotion, and support to sell and ship their DIY electronic projects to customers worldwide through the Elecrow platform, solving various challenges from production to sales!

With this project, makers can focus more on innovation and development, while we handle the complex aspects of production, sales, and marketing. The Partner Seller program not only helps makers achieve their commercialization goals but also gives creative projects a chance to be seen by a global audience.

We look forward to collaborating with more creative and ambitious makers to bring these great ideas to the world!

I am experiencing a persistent connectivity issue with my Elecrow C6 eBUS Adapter (based on an ESP32-C6, rev 2 chip). The stick works perfectly after manual configuration, but after a Home Assistant OS reboot, the stick loses its working configuration (presumably Plain Mode).
I currently do not have physical access to my C6 eBUS stick, as the system is running in my holiday/summer house, and am therefore seeking a remote solution to resolve this issue, which unfortunately makes troubleshooting somewhat difficult.

Crucially, functionality is only restored by accessing the stick's Web GUI via Wi-Fi and saving the settings again, which forces the necessary configuration to be written to the stick's memory.

My Setup:
Adapter: Elecrow C6 eBUS Adapter
Chip ID: ccba97f8e568 (ESP32-C6, rev 2)
Firmware Build: 20250216 (Crucial detail for support)
Platform: Home Assistant OS with eBUSd Add-on (v25.1.p20250414).
Connection: USB serial (/dev/serial/by-id/usb-Espressif_...).
Symptom: eBUSd loses communication and never shows signal acquired after an HA reboot.

I have confirmed that the issue cannot be resolved by standard commands, confirming that the high-level "SAVE" function of the GUI is the missing piece:

eBUSd CLI (Port 8888) & Direct Serial Commands: All known remote commands designed to set the mode (plainmode, set mode plain, mode 0) failed to restore functionality, proving that simple serial commands do not replicate the necessary configuration and save action.

Forced Enhanced Protocol: Changing the eBUSd configuration to use the Enhanced Mode protocol (--device=ens:/dev/serial/...) made the stick recognized as enhanced in the log, but communication was still lost (no signal acquired).

Is a firmware update a known and confirmed fix for the C6/ESP32 adapter to resolve the issue of settings persistence (i.e., failure to save operating mode to NVRAM) after a power cycle/reboot?

Is there a newer firmware build available than 20250216 that specifically addresses this persistence issue?

Is there an undocumented high-level CLI command (or sequence) that replicates the "Save Settings" function via serial access (which I have via SSH) that bypasses the need for the Web GUI?

Thank you for any technical guidance!

int backlightPin = 2;
if (strcmp(topic, "elecrow/backlight/state") == 0) {
if (message == "on") {
digitalWrite(backlightPin, HIGH); // Turns on backlight
} else {
digitalWrite(backlightPin, LOW); // Turns off backlight
}
Serial.println("Backlight: " + message);
}

Looking at Serial Monitor I see
Backlight: on
Backlight: off
As proof that it is passing this section ok.
Any advise would be helpfull.

💡What is Elecrow Dropshipping?
In a nutshell, the Elecrow dropshipping service allows you to sell without holding inventory. You just pass the orders to us, and we handle everything from packaging to shipping—super convenient and efficient! It’s a lifesaver for sellers who want to focus on product development, marketing, or customer service.

Key Features:

📦End-to-End Dropshipping:
Once you receive an order on your store or platform, simply forward the order details to Elecrow (or place it directly on their website). We pick the products from their inventory, pack them, and ship them directly to your customers. It covers all products on its website and even supports electronic products or samples from your store—very flexible!

💰Transparent Pricing:
Dropshipping fee formula: Shipping cost × 1.1 + $1.5.
This fee includes packaging materials (bubble bags, cartons, etc.) and labor costs (dedicated packers and address verification). Costs are calculated based on product weight, shipping method, and destination, and you’ll know the exact fees before paying—no surprises.

📬Global Shipping Support:
Elecrow has an advanced warehousing and logistics system, prioritizing order processing for quick turnaround. We offer international shipping services, delivering to customers worldwide while keeping shipping costs as low as possible—great value for money.

⚙️Who’s It For?
Online store owners selling PCBs, electronic components, or hardware products.
Entrepreneurs running crowdfunding or sales on platforms like Kickstarter, eBay, or Tindie.
Small teams or individuals looking to expand globally without dealing with inventory or logistics.

If you are interested in our service, feel free to leave us a comment.:)